Herald steering wheel (6 replies)
I recently purchased a 1962 herald 1200 steering wheel to restore. My question is this, is anyone in need of a restored herald wheel and once finished, and I go to list it for sale, is it the same...
View ArticleMy 63 Saloon restoration and convertible questions (3 replies)
Hey all. Just wanted to share the body off restoration so far. Rolling chassis is complete. Pretty excited and nervous about the first drive (when it comes) being this is my first mechanical venture...
View Article64 Sport 6 (1 reply)
Would a 64 Sport 6 tranny be a 4 synchro? Would a 64 bell housing mate up to a later[68?] GT-6 tranny?
View ArticleAcceleration flat spot (6 replies)
I have a 62 convertible that the previous owner had a 71 spit engine installed. It has been sitting on Jack stands in the barn for 20 years. I have rebuilt the carbs and they are tuned sweetly....
View ArticleModern engine swop (7 replies)
Hi I'm looking at a 1971 herald convertible with a knackered engine. Is there a modern engine that fits easily enough? Also break upgrade. Is there a modern bolt on upgrade? 1st time classic owner so...
View Article948 Engine (9 replies)
Searching for a 948 engine to rebuild for my 1960 Standard Ten. Could be from an early Spitfire or Herald. Anyone out there with one to sell?
View Articlebodywork parts identification (1 reply)
Re: Vitesse convertible Mk 1. Can anyone identify the 2 components pictured?. I can't think of where they came from and would like to put them where they belong in my re-build. Sorry, no prizes but my...
View ArticleSeeking a spare wheel for my 63 Herald (3 replies)
Hi Everyone, Might anyone know a decent wheel that could be used as a spare on my 63 Herald? Currently installed tire/wheel information Bead to bead: 14 inches Bolt pattern: Square with studs 3.75ins...
View ArticleHerald chassis modifications - we've started. (16 replies)
I have started modifications to our Herald Mk1 chassis to add some stiffness to it, for the fibreglass 'special' body that we are going to place on the top. The goal is the get to a minimum of...
View ArticleFuel line plugged? (11 replies)
When I disconnected the fuel line from the pump and drained the gas for the winter, I noticed after I filled the tank the fuel line seems plugged. I tried compressed air to blow it out no luck. I am...
View Article1300 engine wanted Adelaide Australia (4 replies)
Hi all, chasing a 1300 motor to put into my spitfire. GE or GK prefix for the Herald unit or FD, FE or FH prefix on the Spitfire one. Running one would be good but a complete rebuildable is ok. Happy...
View ArticlePlease recommend a rust neutralizer for frame (3 replies)
Hi Everyone, My 63 Herald has solid frame but I am moving it to a lakeside community. I think it is best if put a rust inhibitor on the frame to avoid a headache at a later time I'm looking for a...
View ArticleKnowledge request - Speedo pinion seals 69/1360 (no replies)
Greetings. The speedo cable on my 1969 13/60 is slowly dripping oil and I want to replace the seals. I need to make sure I buy the correct ones. The plastic gear-housing for the Speedo Drive Pinion in...
View ArticleLooking to buy Vitesse (no replies)
Anyone have a decent Vitesse hardtop for sale ? Thanks
View ArticleAlmost there, just the seatbelts to go.... (1 reply)
Hello everyone, me and my lad are just about to put our project herald back onthe road, we've sorted the bodywork and the mechanicals but are just replacing the seatbelts... To keep it easy we have...
View ArticleReplace PCV on my '68 13/60 engine (3 replies)
Hi, I've bought a new PCV to replace the one I have. Now I'm looking to remove the old one but there are no screws/bolts around it. Have anyone did that? Can you share pics/video? Thanks.
View ArticleFuel Additive Recommendation (5 replies)
Hello everyone. Looking for recommendations for a good fuel additive for our 67 Herald. Thank you �
View Article[Solved] Dash pad repair (2 replies)
So I was painting some suspension parts on my wife's tbird and had to look up some directions on the POR15 website and saw a little blurb about using it to restore old cardboard parts. I looked at my...
View ArticleSun visor mounts (1 reply)
So I have 3 sun visors that came in a box of parts with my Herald but no mounts for the ends. Does anyone know where these might be able to be purchased?
View Article
More Pages to Explore .....